INSTRUCTIONS FOR KIT #2004652 DUAL
KIT
FITS 1997-2002 FULL-SIZE FORD 1/2 & 3/4 TON 2WD & 4WD PICKUPS
W/V-8 & 6 CYL. WITH 2-1/2" EXHAUST AT CONVERTER. THIS KIT
FITS ALL WHEEL BASE MODELS. DOES NOT FIT DIESEL, V-10, LIGHTNING
OR SUPER DUTY.
NOTE: DO NOT TIGHTEN ANY CLAMPS OR BOLTS UNTIL THE LAST STEP!
1) REMOVE THE EXHAUST SYSTEM AT THE CLAMP BEHIND THE CONVERTERS
LEAVING ONLY THE ORIGINAL Y PIPE, RUBBER MOUNTS, AND CATALYTIC
CONVERTERS ON THE TRUCK.
NOTE: THE EXTENSION PIPE WILL FIT THE LONGER WHEEL BASE TRUCKS
WITHOUT CUTTING. ON ALL OTHER VEHICLES THE EXTENSION PIPE WILL
NEED TO BE CUT FROM THE 3" O.D. END (THE END THAT IS NOT SHRUNK) AS
NECESSARY.
2) SLIP THE FRONT PIPE INTO PLACE. WITH THE TAIL PIPES IN
THE REAR OF THE MUFFLER, HOLD UP THE MUFFLER AND TAIL PIPES IN A
POSITION THAT CLEARS ALL CHASSIS COMPONENTS. MARK THE FRONT
PIPE. MAKE SURE TO ACCOUNT FOR AT LEAST 2" OF THE PIPE TO GO INTO
THE MUFFLER. CUT THE FRONT PIPE.
3) USE THE 2-1/2" CLAMP TO ATTACH THE EXTENSION PIPE TO THE
CONVERTER PIPE.
4) USE THE 3" MUFFLER CLAMP TO ATTACH THE INLET OF THE MUFFLER
AND THE EXTENSION PIPE TOGETHER.
5) INSTALL THE LEFT TAIL PIPE USING A 2-1/2" CLAMP TO THE LEFT
OUTLET OF THE MUFFLER.
6) INSTALL AN I.D/O.D TAIL PIPE EXTENSION TO THE LEFT TAIL
PIPE. (YOU WILL WANT TO TRIM THE EXTENSION TO YOUR DESIRED
LENGTH.)
7) LOCATE OR DRILL A HOLE IN THE FRAME NEAR THE END OF THE OVER
THE AXLE SECTION OF THE LEFT TAIL PIPE BEFORE THE LAST BEND.
USING THE 5/16 X 1" BOLT, NUT, LOCK AND FENDER WASHER, INSTALL THE
THU-900 (360 SWINGER HANGER) TO THE FRAME AND ATTACH TO THE LEFT TAIL
PIPE USING A 2-1/2" CLAMP. NOTE: BOTH TAIL PIPES ARE ROUTED
BETWEEN THE SHOCK AND THE SPARE TIRE. THE LEFT TAIL PIPE HAS A 48
DEG. FIRST BEND AND 65 DEG. LAST BEND, AND THE RIGHT TAIL PIPE HAS A 30
DEG. FIRST BEND AND 65 DEG. LAST BEND.
8) INSTALL THE RIGHT TAIL PIPE USING A 2-1/2" CLAMP TO THE RIGHT
OUTLET OF THE MUFFLER.
9) LOCATE OR DRILL A 5/16" HOLE IN THE FRAME ABOVE EITHER OUTLET
OF THE MUFFLER. INSTALL A THU-900 SWINGER HANGER TO THE FRAME
USING A 5/16" X 1" BOLT, NUT, LOCK WASHER, AND FENDER WASHER.
CONNECT THE HANGER AND EITHER SIDE CONNECTION POINT OF THE LEFT OR
RIGHT TAIL PIPE AND MUFFLER USING A 2-1/2" CLAMP.
10) INSTALL AN I.D/O.D TAIL PIPE EXTENSION TO THE RIGHT TAIL
PIPE. (YOU WILL WANT TO TRIM THE EXTENSION TO YOUR DESIRED
LENGTH.)
11) LOCATE OR DRILL A HOLE IN THE FRAME NEAR THE END OF THE OVER
THE AXLE SECTION OF THE LEFT TAIL PIPE BEFORE THE LAST BEND.
USING THE 5/16" X 1" BOLT, NUT, LOCK AND FENDER WASHER, INSTALL THE
THU-900 (360 SWINGER HANGER) TO THE FRAME AND CONNECT TO THE LEFT TAIL
PIPE USING A 2-1/2" CLAMP.
12) TIGHTEN ALL CLAMPS AND BOLTS AND CHECK FOR CLEARANCE OF THE
FRAME, BODY, AND BRAKE AND FUEL LINES.
HARDWARE KIT FOR KIT #2004652
7) 2-1/2" CLAMPS
1) FRONT EXTENSION PIPE
1) 3" CLAMP
1) LEFT TAIL PIPE
3) 5/16" NUTS
1) RIGHT TAIL PIPE
3) THU-900 (360 SWINGER HANGER)--(BR91930)
2) TAIL PIPE EXTENSIONS
3) 5/16" X 1" BOLTS
1) MUFFLER #1373
3) FENDER WASHERS
3) 5/16" LOCK WASHERS
DANGER WARNING: SHOULD THE PURCHASER DECIDE TO INSTALL THIS, OR
ANY OTHER EXHAUST PRODUCT AT HOME, BE WARNED THAT PLEASURE CAR OR LIGHT
DUTY TRUCK/VAN "BUMPER JACKS" ARE INTENDED FOR EMERGENCY USE
ONLY. THE USE OF FRAME CONTACT JACK STANDS IN CONJUNCTION WITH A
FLOOR JACK AS MAIN SUPPORT IS HIGHLY RECOMMENDED TO MINIMIZE ACCIDENTAL
DROPPING OF A VEHICLE WHILE THE INSTALLATION PROCEEDS.
Limitation of liability--Disclaimers: The regulation of emissions
production, noise levels and safety standards is undertaken by the
federal government, each of the fifty state legislatures, and by many
local municipalities, towns and counties.
The manufacturer makes no warranties of
merchantability, of fitness for a particular purpose, or that its
products are approved for general use, or that its products comply with
laws, regulations or ordinances in the states where they may be sold to
the ultimate purchaser, the consumer.
The entire risk as to the conformity of this product
in any such state and as to repair, should the product prove to be
defective or non-conforming, is on the retail purchaser, the buyer, the
ultimate consumer of such product and it is not upon the seller,
distributor, or manufacturer.
In this connection, retail purchaser, the buyer, the
ultimate consumer assumes the burden of the entire cost of any and all
necessary service, alterations, and or repair.
The foregoing statement limits the liability of the
manufacturer.
Heartthrob Exhaust Accessories are manufactured in--Litchfield, Mn