INSTRUCTIONS FOR KIT #2005025 DUAL KIT
FITS 2003 FULL-SIZE DODGE 1/2 & ¾ TON RAM W/5.7L V8 HEMI
ONLY, 2WD & 4WD, ALL WHEEL BASES, DOES NOT FIT DIESEL, V6, 5.9L OR
4.7L, AND V-10.
NOTE: DO NOT TIGHTEN ANY CLAMPS OR BOLTS UNTIL THE LAST STEP!
1) REMOVE THE EXHAUST SYSTEM AT THE CLAMP AT THE MUFFLER LEAVING
ONLY THE ORIGINAL Y PIPE, RUBBER MOUNTS, CATALYTIC CONVERTER, AND O.E.
EXTENSION PIPE ON THE TRUCK. YOU MAY NEED TO USE A LUBRICANT TO
REMOVE THE WIRE HANGERS FROM THE O.E. RUBBER MOUNTS.
2) THE FRONT EXTENSION PIPE WILL FIT ALL WHEEL BASE TRUCKS
WITHOUT CUTTING. USE A 3"
CLAMP TO ATTACH THE EXTENSION PIPE TO THE O.E. EXTENSION PIPE, BE SURE
TO LINE UP THE NOTCH. (THE EXTENSION PIPE WILL SHIFT THE EXHAUST
AWAY FROM THE DRIVE SHAFT).
3) USE A 3" MUFFLER CLAMP TO ATTACH THE INLET OF THE MUFFLER AND
THE FRONT EXTENSION PIPE TOGETHER.
4) INSTALL THE LEFT TAIL PIPE (4 BENDS) USING THE LEFT 2-1/2”
HANGER CLAMP (SHORTER) TO THE LEFT OUTLET OF THE MUFFLER. CONNECT
THE WIRE PORTION OF THE HANGER TO THE O.E. RUBBER MOUNT ABOVE THIS
CONNECTING POINT.
5) INSTALL THE LEFT TAIL PIPE EXTENSION (42-1/2”) TO THE LEFT
TAIL PIPE USING A 2-1/2” CLAMP.
6) LOCATE OR DRILL A HOLE IN THE FRAME NEAR THE MIDDLE OF THE
LEFT TAIL PIPE EXTENSION. (THERE IS A LARGE 1” WIDE HOLE THAT IS
IDEAL TO USE). USING THE 3/8” X 3-1/2" BOLT, NUT, LOCK, FENDER
AND LARGE WASHER (INSTALL THE SMALLER FENDER WASHER TO THE BOLT FIRST,
THEN INSTALL THE LARGER WASHER), INSTALL THE BR91930 (360 SWINGER
HANGER) TO THE FRAME AND ATTACH TO THE LEFT TAIL PIPE EXTENSION USING A
2-1/2" CLAMP.
7) INSTALL THE RIGHT TAIL PIPE (5 BENDS) USING THE RIGHT 2-1/2"
HANGER CLAMP (LONGER) TO THE RIGHT OUTLET OF THE MUFFLER. CONNECT
THE WIRE PORTION OF THE HANGER TO THE O.E. RUBBER MOUNT ABOVE THIS
CONNECTING POINT.
8) LOCATE OR DRILL A HOLE IN THE FRAME NEAR THE CONNECTING POINT
OF THE RIGHT TAIL PIPE AND THE RIGHT TAIL PIPE EXTENSION
(31-1/2”). (THERE IS A LARGE 1” WIDE HOLE THAT IS IDEAL TO
USE). USING THE 3/8” X 3-1/2" BOLT, NUT, LOCK, FENDER AND LARGE
WASHER (INSTALL THE SMALLER FENDER WASHER TO THE BOLT FIRST, THEN
INSTALL THE LARGER WASHER), INSTALL THE BR91930 (360 SWINGER HANGER) TO
THE FRAME AND ATTACH TO THE RIGHT TAIL PIPE AND EXTENSION USING A
2-1/2" CLAMP. (YOU WILL WANT TO TRIM BOTH OF THE EXTENSIONS TO
YOUR DESIRED LENGTH.)
9) TIGHTEN ALL CLAMPS AND BOLTS AND CHECK FOR CLEARANCE OF THE
FRAME, BODY, AND BRAKE AND FUEL LINES.
HARDWARE KIT FOR KIT #2005025, :
4) 2-1/2” CLAMPS
1) FRONT
EXTENSION PIPE #2005026
2) 3” CLAMPS
1) LEFT TAIL PIPE #2005027
1) LEFT 2-1/2” HANGER CLAMP-# 2968
1) RIGHT TAIL PIPE #2005028
1) RIGHT 2-1/2” HANGER CLAMP-#2967
1) LEFT TAIL PIPE EXTENSION (42-1/2”
LONG)
2) 360 SWINGER HANGER-BR91930
1) MUFFLER #1373
2) 3/8" X 3-1/2" BOLTS
1) RIGHT TAIL PIPE
EXTENSION (31-1/2” LONG)
2) 3/8" NUTS
2) #33012 1/2” LARGE WASHERS
2) #33219 3/8” FENDER WASHERS
2) 3/8" LOCK WASHERS
DANGER WARNING: SHOULD THE PURCHASER DECIDE TO INSTALL THIS, OR
ANY OTHER EXHAUST PRODUCT AT HOME, BE WARNED THAT PLEASURE CAR OR LIGHT
DUTY TRUCK/VAN "BUMPER JACKS" ARE INTENDED FOR EMERGENCY USE
ONLY. THE USE OF FRAME CONTACT JACK STANDS IN CONJUNCTION WITH A
FLOOR JACK AS MAIN SUPPORT IS HIGHLY RECOMMENDED TO MINIMIZE ACCIDENTAL
DROPPING OF A VEHICLE WHILE THE INSTALLATION PROCEEDS.
Limitation of liability--Disclaimers: The regulation of emissions
production, noise levels and safety standards is undertaken by the
federal government, each of the fifty state legislatures, and by many
local municipalities, towns and counties.
The manufacturer makes no warranties of
merchantability, of fitness for a particular purpose, or that its
products are approved for general use, or that its products comply with
laws, regulations or ordinances in the states where they may be sold to
the ultimate purchaser, the consumer.
The entire risk as to the conformity of this product
in any such state and as to repair, should the product prove to be
defective or non-conforming, is on the retail purchaser, the buyer, the
ultimate consumer of such product and it is not upon the seller,
distributor, or manufacturer.
In this connection, retail purchaser, the buyer, the
ultimate consumer assumes the burden of the entire cost of any and all
necessary service, alterations, and or repair.
The foregoing statement limits the liability of the
manufacturer.
Heartthrob Exhaust Accessories are manufactured by CREMCO--Litchfield,
Mn
For detailed digital installation pictures, email us at
heartthrob@willmar.com