INSTRUCTIONS FOR KIT #2008351    SINGLE EXHAUST KIT       

FITS 1994-1995 FULL-SIZE GM 1/2 & 3/4 TON 2WD & 4WD PICKUPS W/4.3L V-6, 5.0 L & 5.7L V-8 WITH 2-3/4" FLANGED EXHAUST AT CONVERTER.  THIS KIT FITS ALL WHEEL BASE MODELS.  

NOTE:  DO NOT TIGHTEN ANY CLAMPS OR BOLTS UNTIL THE LAST STEP!

1)  REMOVE THE EXHAUST SYSTEM AT THE FLANGE BEHIND THE CONVERTER LEAVING ONLY THE ORIGINAL Y PIPE, RUBBER MOUNTS FOR HANGERS, AND THE CATALYTIC CONVERTER ON THE TRUCK.  YOU WILL NEED TO REUSE THE ORIGINAL NUTS TO FASTEN THE FLANGE TO THE EXHAUST.

NOTE:  THE FLANGED FRONT PIPE WILL NEED TO BE CUT TO FIT THE REGULAR CAB MODELS.  THIS PIPE FITS EXTENDED CAB SHORT BOX MODELS WITHOUT CUTTING.  FOR EXTENDED CAB LONG BOX MODELS, AN ADDITIONAL EXTENSION PIPE IS INCLUDED WITH AN EXTRA CLAMP.  THESE PIECES ARE NOT NEEDED ON THE OTHER THREE MODELS.

2)  SLIP THE FLANGED FRONT PIPE INTO PLACE AND SLIDE THE FLANGE ON THE PIPE (FLAT SIDE FIRST) TO THE CONVERTER FLANGE.  INSTALL THE NUTS TO THE BOLTS AT THE FLANGE BUT DON’T TIGHTEN YET.

FOR THOSE WITH REGULAR CAB SHORT BOX MODELS, CUT 23” OFF THE FLANGED FRONT PIPE FROM THE END THAT IS 3” O.D.  FOR THOSE WITH REGULAR CAB LONG BOX MODELS, CUT 10” OFF THE FLANGED FRONT PIPE FROM THE END THAT IS 3” O.D..  FOR THOSE WITH EXTENDED CAB SHORT BOX, GO TO STEP 3).  FOR THOSE WITH EXTENDED CAB LONG BOX, ADD THE 17” LONG EXTENSION PIPE AND ATTACH TO THE FLANGED FRONT PIPE USING A 3” CLAMP.

3)  INSTALL THE 3” HANGER CLAMP TO THE FLANGED FRONT PIPE AT THE FRONT O.E. RUBBER MOUNT.

4)  USE A 3" MUFFLER CLAMP TO ATTACH THE INLET OF THE MUFFLER AND THE FRONT FLANGED PIPE TOGETHER.  THE OUTLET OF THE MUFFLER SHOULD LIE TOWARDS THE DRIVE SHAFT OF THE VEHICLE.

5)  INSTALL THE OVER THE AXLE SECTION OF THE TAIL PIPE USING A 3" CLAMP TO THE OUTLET OF THE MUFFLER.  THE INLET OF THE OVER THE AXLE TAIL PIPE HAS A 24 DEGREE BEND, THE OUTLET A 74 DEGREE BEND.

6)  INSTALL THE MIDDLE  HANGER TO THE FRONT SECTION OF THE TAIL PIPE AT THE MIDDLE O.E. RUBBER MOUNT.  

7)  INSTALL THE REAR SECTION OF THE TAIL PIPE.  INSTALL THE REAR HANGER TO THE REAR O.E. RUBBER HANGER MOUNT.  USE THE REAR HANGER TO CONNECT THE FRONT AND REAR TAIL PIPES TOGETHER.  

HARDWARE KIT FOR KIT #2008351
1)  REAR HANGER-#2934           
1)  FRONT FLANGED PIPE
3)  3" CLAMP                   
1)  OVER THE AXLE TAIL PIPE #2005500-2
1)  FRONT HANGER-#2954
1)  REAR TAIL PIPE #2005500-3        
1)  MIDDLE HANGER-#2932           
1)  MUFFLER #1142
1)  FLANGE                   
1)  17” LONG 3” ID/OD EXTENSION PIPE
    
        

Part # 2008351    JCW # 49-7279
Limitation of liability--Disclaimers:  The regulation of emissions production, noise levels and safety standards is undertaken by the federal government, each of the fifty state legislatures, and by many local municipalities, towns and counties.
    The manufacturer makes no warranties of merchantability, of fitness for a particular purpose, or that its products are approved for general use, or that its products comply with laws, regulations or ordinances in the states where they may be sold to the ultimate purchaser, the consumer.
    The entire risk as to the conformity of this product in any such state and as to repair, should the product prove to be defective or non-conforming, is on the retail purchaser, the buyer, the ultimate consumer of such product and it is not upon the seller, distributor, or manufacturer.  
    In this connection, retail purchaser, the buyer, the ultimate consumer assumes the burden of the entire cost of any and all necessary service, alterations, and or repair.
    The foregoing statement limits the liability of the manufacturer.

DANGER WARNING:  SHOULD THE PURCHASER DECIDE TO INSTALL THIS, OR ANY OTHER EXHAUST PRODUCT AT HOME, BE WARNED THAT PLEASURE CAR OR LIGHT DUTY TRUCK/VAN "BUMPER JACKS" ARE INTENDED FOR EMERGENCY USE ONLY.  THE USE OF FRAME CONTACT JACK STANDS IN CONJUNCTION WITH A FLOOR JACK AS MAIN SUPPORT IS HIGHLY RECOMMENDED TO MINIMIZE ACCIDENTAL DROPPING OF A VEHICLE WHILE THE INSTALLATION PROCEEDS.
 
Heartthrob Exhaust Accessories are manufactured in--Litchfield, Mn