KIT #4150SK, 4150GP
1965-1976 FORD PICKUP 1/2 & 3/4 TON 2WD V-8 332-390 EXCEPT 351  

NOTE:  THIS DUAL KIT WILL NOT FIT SUPER CABS.

DANGER WARNING:  SHOULD THE PURCHASER DECIDE TO INSTALL THIS EXHAUST PRODUCT AT HOME, BE WARNED THAT PLEASURE CAR OR LIGHT DUTY TRUCK/VAN “BUMPER” JACKS ARE INTENDED FOR EMERGENCY USE ONLY.  THE USE OF FRAME CONTACT JACK STANDS IN CONJUNCTION WITH A FLOOR JACK AS MAIN SUPPORT IS HIGHLY RECOMMENDED TO MINIMIZE ACCIDENTAL DROPPING OF A VEHICLE WHILE THE INSTALLATION PROCEEDS.  

HARDWARE KIT:            
4)  LB7 HANGERS                                 1)  #3150-2 LEFT MANIFOLD PIPE
4)  SNAPPER GROMMETS                   1)  #3150-1 RIGHT MANIFOLD PIPE
4)  5/16” X 1-1/2” BOLTS                       1)  #3150L-2 RIGHT EXTENSION
4)  5/16” NUTS                                        1)  #3150R-2 LEFT EXTENSION
10)  2-1/4” CLAMPS                               1)  #45575R RIGHT TAIL PIPE
2)  EG24111 GASKETS                          1)  #45575L LEFT TAIL PIPE
 
                    
LIMITATION OF LIABILITY-DISCLAIMERS:  THE REGULATION OF EMISSIONS PRODUCTION, NOISE LEVELS AND SAFETY STANDARDS IS UNDERTAKEN BY THE FEDERAL GOVERNMENT, EACH OF THE FIFTY STATE LEGISLATURES, AND BY MANY LOCAL MUNICIPALITIES, TOWNS AND COUNTIES.
    THE MANUFACTURER MAKES NO WARRANTIES OF MERCHANTABILITY, OF FITNESS FOR A PARTICULAR PURPOSE, OR THAT ITS PRODUCTS ARE APPROVED FOR GENERAL USE, OR THAT  ITS PRODUCTS COMPLY WITH LAWS, REGULATIONS OR ORDINANCES IN THE STATES WHERE THEY MAY BE SOLD TO THE ULTIMATE PURCHASER, THE CONSUMER.
    THE ENTIRE RISK AS TO THE CONFORMITY OF THIS PRODUCT IN ANY SUCH STATE AND AS TO REPAIR, SHOULD THE PRODUCT PROVE TO BE DEFECTIVE OR NON-CONFORMING, IS ON THE RETAIL PURCHASER, THE BUYER, THE ULTIMATE CONSUMER, OF SUCH PRODUCT AND IT IS NOT UPON THE SELLER, DISTRIBUTOR, OR MANUFACTURER.  
    IN THIS CONNECTION, THE RETAIL PURCHASER, THE BUYER, THE ULTIMATE CONSUMER ASSUMES THE BURDEN OF THE ENTIRE COST  OF ANY AND ALL NECESSARY SERVICE, ALTERATIONS AND OR REPAIR.  
    THE FOREGOING STATEMENT LIMITS THE LIABILITY OF THE MANUFACTURER.
    CALIFORNIA VEHICLE CODE SECTION 27156 PROHIBITS THE ADVERTISING, OFFERING FOR SALE, OR INSTALLATION OF ANY DEVICE WHICH MODIFIES A VEHICLE’S EMISSION CONTROL SYSTEM.  THIS PRODUCT IS  THEREFORE NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON VEHICLES EQUIPPED WITH CATALYTIC CONVERTERS.

INSTALLATION INSTRUCTIONS:

NOTE:  DO NOT TIGHTEN ANY CLAMPS OR NUTS UNTIL THE LAST STEP!!

1)  REMOVE THE OLD EXHAUST SYSTEM.  SAVE THE OLD FLANGES FROM THE ORIGINAL FRONT PIPE.  

2)  INSTALL THE LEFT (#3150-2—SINGLE BEND) AND RIGHT (#3150-1—TWO BENDS) MANIFOLD PIPES USING THE INCLUDED GASKETS AND ORIGINAL FLANGES.  YOU WILL NEED TO USE YOUR ORIGINAL MANIFOLD STUDS AND NUTS.  TIGHTEN ONLY ENOUGH TO HOLD IN PLACE.

3)  INSTALL THE LEFT AND RIGHT FRONT EXTENSION PIPES TO THE MANIFOLD PIPES USING 2-1/4” CLAMPS.  CLAMP LIGHTLY INTO PLACE.  

4)  INSTALL THE MUFFLERS ONTO THE FRONT EXTENSION PIPES USING 2-1/4” CLAMPS.  ROTATE THE MUFFLERS FOR CLEARANCE FROM THE DRIVE SHAFT AND FRAME.  NOTE:  IF YOU ARE USING GLASS PACKS, THE EXHAUST SHOULD GO OVER, AND NOT DIRECTLY INTO, THE LOUVERS.

5)  LOCATE THE CROSS MEMBER IN THE FRAME--EITHER IN FRONT OF OR IN THE REAR OF THE MUFFLERS.  DRILL A 5/16” HOLE AND MOUNT THE LB7 HANGERS TO THE FRAME USING THE INCLUDED 5/16” X 1-1/2” BOLTS, NUTS, AND SNAPPER GROMMET.  CLAMP THE EXHAUST SYSTEM TO THE HANGERS.  

6)  INSTALL THE LEFT AND RIGHT TAIL PIPES TO THE MUFFLERS USING 2-1/4” CLAMPS.  

7)  MOUNT THE REMAINING LB7 HANGERS AND HARDWARE TO THE FRAME NEAR THE REAR EXIT LOCATION OF THE TAIL PIPES.  CLAMP THE TAIL PIPES TO THE HANGERS USING 2-1/4” CLAMPS.  

8)  MAKE SURE THAT ALL THE PARTS OF THE SYSTEM ARE CLEAR OF FRAME MEMBERS, ALL HOSES, SUSPENSION, AND BRAKE AND FUEL LINES.  STARTING AT THE EXHAUST MANIFOLDS, TIGHTEN ALL CONNECTIONS AND NUTS.  MAKE SURE ALL PARTS ARE CLEAR AND WILL NOT LEAK OR RATTLE.  AFTER SEVERAL DAYS OF DRIVING RETIGHTEN ALL BOLTS